View STPS5L60S_4611141.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

STPS5L60
Power Schottky rectifier
Features

Negligible switching losses Low forward voltage drop for higher efficiency Low thermal resistance Avalanche capability specified
K A
A K
Description
Power Schottky rectifier suited for switch mode power supplies and high frequency inverters. This device is intended for use in low voltage output for small battery chargers and consumer SMPS such as DVD and set-top-box.
SMC STPS5L60S DO-201AD STPS5L60
Table 1.
Device summary
IF(AV) VRRM Tj (max) VF (max) 5A 60 V 150 C 0.53 V
May 2008
Rev 3
1/8
www.st.com 8
Characteristics
STPS5L60
1
Table 2.
Symbol VRRM IF(RMS) IF(AV)
Characteristics
Absolute ratings (limiting values)
Parameter Repetitive peak reverse voltage RMS forward current DO-201AD Average forward current SMC Surge non repetitive forward current Repetitive peak avalanche power Storage temperature range Maximum operating junction temperature(1) Tl = 100 C = 0.5 Tl = 100 C = 0.5 Value 60 15 5 Unit V A A
IFSM PARM Tstg Tj dV/dt
1.
dPtot --------------dTj
Half wave, single phase tp = 10 ms tp = 1 s Tj = 25 C
150 4000 -65 to + 175 150 10000
A W C C V/s
Critical rate of rise of reverse voltage (rated VR, Tj = 25 C)
1 < -------------------------- condition to avoid thermal runaway for a diode on its own heatsink Rth ( j - a )
Table 3.
Symbol Rth (j-a) Rth (j-l) Rth (j-l)
Thermal parameters
Parameter Junction to ambient DO-201AD Junction to leads Junction to leads SMC Lead length = 10mm 15 15 Value 75 C/W Unit
Table 4.
Symbol
Static electrical characteristics
Parameter Tests conditions Tj = 25 C Min. Typ. Max. 0.22 VR = VRRM 10 40 0.47 IF = 5 A 0.43 0.42 25 100 0.52 0.49 0.48 V mA Unit
IR (1)
Reverse leakage current
Tj = 100 C Tj = 125 C Tj = 25 C
VF (1)
Forward voltage drop
Tj = 100 C Tj = 125 C
1. Pulse test : tp = 380 s, < 2%
To evaluate the conduction losses use the following equation : P = 0.39 x IF(AV) + 0.028x IF2(RMS)
2/8
STPS5L60
Characteristics
Figure 1.
PF(av)(W)
3.5
Conduction losses versus average Figure 2. current
= 0.05 = 0.1 = 0.2 = 0.5
Average forward current versus ambient temperature ( = 0.5)
6
IF(av)(A)
Rth(j-a)=Rth(j-l)
3.0 2.5 2.0
=1
5
4
3
1.5
2
DO-201AD Rth(j-a)=75C/W
1.0
T
T
0.5
1
SMC Rth(j-a)=90C/W
IF(av)(A)
0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
=tp/T
5.0 5.5
tp
=tp/T
0
tp
Tamb(C)
50 75 100 125 150
6.0
0
25
Figure 3.
Normalized avalanche power derating versus pulse duration
Figure 4.
Normalized avalanche power derating versus junction temperature
PARM(tp) PARM(1s)
1
PARM (t j ) PARM (25C)
1
0.1
0.01
0.001
0.01 0.1 1
tp(s)
10 100 1000
Tj (C)
0 25 50 75 100 125 150
Figure 5.
Non repetitive surge peak forward current versus overload duration (maximum values) DO-201AD
DO-201AD
Figure 6.
Non repetitive surge peak forward current versus overload duration (maximum values) SMC
SMC
16 14 12
IM(A)
14 12 10
IM(A)
10 8 6
Ta=25 C
8
Ta=75 C
Ta=25 C
6 4
Ta=75 C
4
IM
Ta=125 C
Ta=125 C
2 0 1.E-03
2
t
IM t =0.5
=0.5
t(s)
1.E-02 1.E-01 1.E+00
t(s)
1.E-02 1.E-01 1.E+00
0 1.E-03
3/8
Characteristics
STPS5L60
Figure 7.
Relative variation of thermal impedance junction to ambient versus pulse duration, DO-201AD
Figure 8.
Relative variation of thermal impedance junction to ambient versus pulse duration, SMC
Zth(j-a)/Rth(j-a)
1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03
DO-201AD
Zth(j-a)/Rth(j-a)
1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2
SMC
tp(s)
0.1 0.0 1.E-01 1.E+00
tp(s)
1.E+01 1.E+02 1.E+03
Figure 9.
Reverse leakage current versus reverse voltage applied (typical values)
Figure 10. Junction capacitance versus reverse voltage applied (typical values)
1000
1.E+03
IR(mA)
Tj=150C
C(pF)
F=1MHz Vosc=30mV Tj=25C
1.E+02
Tj=125C
1.E+01
Tj=100C
1.E+00
Tj=75C
Tj=50C
1.E-01
Tj=25C
1.E-02
VR(V)
1.E-03 0 5 10 15 20 25 30 35 40 45 50 55 60
100 1 10
VR(V)
100
4/8
STPS5L60
Characteristics
Figure 11. Forward voltage drop versus forward current (low level)
5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 0.55 0.60
Tj=25C (Maximum values) Tj=125C (Typical values) Tj=125C (Maximum values)
Figure 12. Forward voltage drop versus forward current (high level)
50 45 40 35 30 25 20 15 10
Tj=25C (Maximum values) Tj=125C (Typical values)
IFM(A)
IFM(A)
Tj=125C (Maximum values)
VFM(V)
5 0 0.0 0.2 0.4 0.6 0.8
VFM(V)
1.0 1.2 1.4 1.6
Figure 13. Thermal resistance junction to ambient versus copper surface under each lead (epoxy printed board FR4, Cu = 35 m) SMC
Rth(j-a)(C/W)
100 90 80 70 60
SMC
Figure 14. Thermal resistance junction to ambient versus copper surface under each lead (epoxy printed board FR4, Cu = 35 m), DO-201AD
80 70 60 50
(j )
Rth(j-a)(C/W)
DO-201AD
50 40 30 20 10 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
40 30 20 10
SCU(cm)
S(cm)
0 1 2 3 4 5 6 7 8 9 10
0
Figure 15. Thermal resistances versus leads length DO-201AD
Rth(C/W)
80 70 60 50 40 30 20 10 0 5 10 15 20 25
Rth(j-l) Rth(j-a): Epoxy printed circuit board FR4 (Cu=35m)
Lleads(cm)
5/8
Package information
STPS5L60
2
Package information
Epoxy meets UL94, V0
In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at www.st.com. Table 5. SMC dimensions
Dimensions Ref.
E1
Millimeters Min. Max. 2.45 0.20 3.20 0.40 6.25 8.15 7.15 4.70 1.50
Inches Min. 0.075 0.002 0.114 0.006 0.218 0.305 0.260 0.173 0.030 Max. 0.096 0.008 0.126 0.016 0.246 0.321 0.281 0.185 0.059
A1
D
1.90 0.05 2.90 0.15 5.55 7.75 6.60 4.40 0.75
A2 b(1)
E
c
(1)
D
A1 C E2 L A2 b
E E1 E2 L
1. Dimensions b and c apply to plated leads
Figure 16. Footprint, dimensions in mm (inches)
1.54 (0.061) 5.11 (0.201) 1.54 (0.061)
3.14 (0.124)
8.19 (0.322)
6/8
STPS5L60 Figure 17. Package mechanical data DO-201AD plastic
Ordering information
Dimensions REF. Millimeters Min.
B
Note 1
Inches Min. Max. 0.374 1.000
Max. 9.50
A E E
Note 1
B
A B C 25.40
OD
Note 2
5.30 1.30 1.25
0.209 0.051 0.049
D E
OC
Notes 1-The lead diameter D is not controlled over zone E 2 - The minimum axial length within which the device may be placed with its leads bent at right angles is 0.59" (15 mm)
3
Ordering information
Table 6. Ordering information
Marking STPS5L60 STPS5L60 S56 Package D0-201AD D0-201AD SMC Weight 1.12 g 1.12 g 0.245 g Base qty 600 1900 2500 Delivery mode Ammopack Tape and reel Tape and reel
Order code STPS5L60 STPS5L60RL STPS5L60S
4
Revision history
Table 7.
Date July-2003 16-May-2008
Document revision history
Revision 2 3 Previous issue. Added ECOPACK statement. Added SMC package. Updated characteristic curves. Description of changes
7/8
STPS5L60
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
8/8

▲Up To Search▲

Price & Availability of STPS5L60S

	To Download STPS5L60S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .